Page 1 of 1

I hate bank holiday weekends.

Posted: |April 18th, 2017|, 5:54 am
by norrie
One I've been working all weekend and two my new carburettors are stuck in Coventry. I could have had them fitted by now. :rant:
I need a drink and make it a large one. :(

Re: I hate bank holiday weekends.

Posted: |April 18th, 2017|, 6:55 am
by andybaggies
I know what you mean, new front pads in the garage & new front discs en-route in some unnamed warehouse, bah! :x

Although it did give me time to pop the caliper pistons out to clean & red rubber grease the seals to, hopefully, cure the sticking brake. Absolute pig to bleed the empty system so I tried the reverse bleeding method, using a syringe to pump fluid up from the caliper, and it worked a treat. Also, fingers crossed, it seems to have cured the dragging brake.

Tot of scotch and we're all sorted.

Andy B

Re: I hate bank holiday weekends.

Posted: |April 18th, 2017|, 8:30 am
by norrie
Sounds good to me. :mrgreen:

Re: I hate bank holiday weekends.

Posted: |April 18th, 2017|, 8:45 am
by snapdragon
Oh my!
Have a pint of virtual scotch :beer:

Re: I hate bank holiday weekends.

Posted: |April 18th, 2017|, 8:36 pm
by norrie
Mmm that's better. :thumbsup:

Re: I hate bank holiday weekends.

Posted: |April 19th, 2017|, 5:46 pm
by nickst4
You have my sympathies for bits stuck in t'post. Conversely, yesterday I received a beautiful new Bitubo rear shock for the Planet (subsequently Raptor 125) that had come all the way from Italy but got stalled over Easter. Can't wait to get that on and enjoy the fun little bike! :thumbsup:

Nick

Re: I hate bank holiday weekends.

Posted: |April 19th, 2017|, 8:17 pm
by andybaggies
All good things come to those who wait

Re: I hate bank holiday weekends.

Posted: |April 20th, 2017|, 5:52 am
by norrie
I'm still waiting as there was customs charges to pay. :doh:

Re: I hate bank holiday weekends.

Posted: |April 20th, 2017|, 5:52 am
by norrie
I'm still waiting as there was customs charges to pay. :doh:

Re: I hate bank holiday weekends.

Posted: |April 28th, 2017|, 7:17 am
by andybaggies
Although it did give me time to pop the caliper pistons out to clean & red rubber grease the seals to, hopefully, cure the sticking brake.
Thought I'd add a little more info on how I did this.

After undoing the master cylinder cap I pushed all the pistons in on one of the calipers and then zip tied two of them down using one of the pads. Pumping the lever pushed the other two out but not completely. I cleaned & greased the pistons in situ but when I pushed them back in one of them required a bit of pressure before it suddenly shot in and... yes you've guessed it the other with a smug pop shot completely out :o followed by most of the fluid in the system. 'kin rs..

So this forced my hand and without any seal kits I had to press on without splitting the calipers. Disconnected the caliper & with one piston out it's seals & bore could be cleaned properly by (very) gently using the round end of a zip tie. Smear of grease on the seals & piston which could then be quite easily pushed back in.

Zip tied the cleaned piston down then used a foot pump with a cut down air bed adaptor in the caliper union hole and out popped the other. Cleaned, greased, re-inserted & zip tied then undid the zip tie on the others back to the foot pump & another pops out. Repeat until all have being done & same on the other caliper. Used a folded rag over the piston before it popped out to save it smacking the opposite piston.

And lo & behold the binding brake was cured , hoorah :D

Andy B

Re: I hate bank holiday weekends.

Posted: |April 28th, 2017|, 3:17 pm
by norrie
Cool. Good write up. It's worthwhile buying a cheap compressor for things like this. Plus there handy to pump your tyres up.